Camcorp Blower Package with M-D Pneumatics Blower Bedienungsanleitung

CAMCORP, Inc.Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com PRESSURE / VACUUM BLOWER PACKAGE INSTRUCTION, OPERATIONS & MAINTENANCE MAN

CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com Symptom Poor Performance Possible Causes Belt Flutter Restricted Inlet Down St

CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com Symptom Leaking Oil Chronic Fuse Blowing or Circuit Breaking Overheating Possi

CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com Pressure and vacuum switches contain one or two single pole, double throw swit

M-D Pneumatics™ Rotary Positive Displacement Air Blower EQUALIZER DF™ 4504 4506 4509 4512 4604 4606 4609 4612 6012 6016 6024 EQUALIZER RM™ Mod

SAFETY INSTRUCTIONS 1. Do not operate before readingthe enclosed instructionmanual.2. Use adequate protection,warning and safety equipmentnecessary to

TABLE OF CONTENTSSAFETY INSTRUCTIONS & WARNING TAGS 2 SAFETY PRECAUTIONS 3 INTRODUCTION 4 OPERATING DATA 4 INSTALLATION 5 LUBRICATION & O

INTRODUCTION CONGRATULATIONS on your purchase of a new EQUALIZER® Rotary Positive Displacement Air Blower from Tuthill Vacuum & Blower Systems. P

INSTALLATION WARNING: Customers are cautioned to provide adequate protection, warning and safety equipment necessary to protect personnel against haz

LUBRICATION Every M-D Pneumatics™ blower from Tuthill Vacuum & Blower Systems is factory tested, oil drained and shipped dry to its installation

PREVENTATIVE MAINTENANCE A good maintenance program will add years of service to your blower. A newly installed blower should be checked frequently du

CAMCORP, Inc.Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com TABLE OF CONTENTS General Information -----------------------------------------

TROUBLESHOOTING Although EQUALIZER® blowers are well designed and manufactured, problems may occur due to normal wear and the need for readjustment.

RECOMMENDED SHUTDOWN PROCEDURE TO MINIMIZE RISK OF FREEZING OR CORROSION When high humidity or moisture is present in an air piping system, condensati

Disassembly of Blower 1. Remove unit from installation and drain lubricant from both ends byremoving magnetic drain plugs [31]. Mark end plates, cove

11 Assembly of Blower The assembly procedure is generally the same for all series, but where there are differences, notations are made. Dowel pins are

12 6. Install keys [24] in rotor shaft keyways. Tight fits are required.7. Lubricate shafts and keys and press drive gear (right hand helix) on drive

13 When removing gear shell from driven gear, it is not necessary to remove gear lock bolt. After completing the timing of the lobes bend over lock ta

SPECIAL TOOL DRAWINGS - MODEL 6000 All dimensions shown are in inches. 14

MAINTENANCE AND SERVICE SPECIFICATIONS SHEET RECOMMENDED LUBRICANTS AND CAPACITIES 15 MODEL RPM PRESSURE PSI (mbar) VACUUM in. Hg (mbar) TEMPERATUR

16 CUTAWAY VIEW - MODELS 4504, 4506, 4509, 4512 When ordering parts, use the item number shown, plus your model and serial number. ITEM PART lbf-ft

17 ITEM DESCRIPTION QTY ITEM DESCRIPTION QTY 1 Rotor, Drive 1 26 Cap Screw 28 2 Rotor, Driven 1 27 Washer 1 3 Housing 1 29 Cap Scre

2 CAMCORP, Inc.Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com GENERAL COMMENTS: CAMCORP supplies air pump packages comprised of positive di

18 CUTAWAY VIEW - MODELS 4604, 4606, 4609, 4612 When ordering parts, use the item number shown, plus your model and serial number. ITEM PART lbf-ft

19 PARTS LIST - MODELS 4604, 4606, 4609, 4612 When ordering parts, use the item number shown, plus your model and serial number. MODEL LOBE TO END PL

CUTAWAY VIEW - MODELS 6012, 6016, 6024 When ordering parts, use the item number shown, plus your model and serial number. ITEM PART lbf-ft (N-m) 2

PARTS LIST - MODELS 6012, 6016, 6024 When ordering parts, use the item number shown, plus your model and serial number. ITEM DESCRIPTION QTY ITEM

22 WARRANTY Subject to the terms and conditions hereinafter set forth and set forth in General Terms of Sale, Tuthill Vacuum & Blower Systems (th

NOTESIMPORTANT All M-D Pneumatics™ blowers manufactured by Tuthill Vacuum & Blower Systems are date coded at time of shipment. In order to assure

NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO. 2912 SPRINGFIELD MO POSTAGE WILL BE PAID BY AD

3 CAMCORP, Inc.Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com PRINCIPLE OF OPERATION CAMCORP blower packages are set up to provide air to a

4 CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com INSTALLATION CAMCORP’s positive displacement blower package consists of a po

CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com LOCKOUT / TAGOUT BEFORE PRE – STARTUP CHECK PRE – START-UP CHECK LIST: A. Che

6 CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com E. Check the amp draw of the motor to be sure that the full load amp rating

7 CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com MAINTENANCE A. Check oil level daily B. Refer to the general lubrication g

CAMCORP, Inc. Phone: 913-831-0740 ~ Fax: 913-831-9271www.camcorpinc.com TROUBLESHOOTING POSITIVE DISPLACEMENT ROTARY BLOWERS Symptom Noisiness Possibl